丁腈橡胶/导电粒子复合材料的正温度系数(PTC)特性

将导电粒子碳黑和铜粉分别与丁腈橡胶混合制备导电聚合物复合材料，其中碳黑（Ｎ５５０）／丁腈橡胶复合材料的电阻率随温度的变化呈现较强的正温度系数（ＰＴＣ）效应。讨论了掺入导电粒子浓度、结构和表面性质以及混炼硫化工艺等对该类材料的室温电阻率及ＰＴＣ效应的影响。     

Recent developments of high-performance NEOMAX magnets

For further improvement in achieving extremely high magnetic properties of Nd- Fe- B sintered magnets, extensive investigation has been done to densify the magnet up to the theoretical value, to increase the volume fraction of the Nd ₂Fe₁₄B matrix phase, and to achieve a high degree of alignment. By controlling chemical composition and the amount of constituent phases,improving particle size distribution, and adopting the isostatic pressing method to get better alignment of fine particles, we have succeeded in obtaining a high-performance magnet having residual flux density (B_r) of 1.495 T (14.95 kG), maximum energy product [(BH)_max] of 431 kj/m³ (54.2 MGOe), and intrinsic coercivity (iH_c) of 845 kA/m (10.62 kOe).     

南洋河水库粘土心墙风化料坝设计与施工控制

结合南洋河水库大坝为粘土心墙风化料坝坝址的自然地形条件，心墙土料不均匀、坝壳料渗透性差的特点，从坝体剖面结构设计、各坝料设计、质量控制标准及基础处理等方面作了分析介绍，以期对类似条件的工程有所借鉴。     

稀土在搪瓷面釉上应用的研究

采用稀土氧化物和无机化合物的复合物（不简称ＲＩ－复合物）作为搪瓷釉浆悬浮剂，使之全部或大部分代替粘土，进行了一系列试验，已获得成功，突破了长期来搪瓷工业离不开粘土的传统工艺，并实现了工业化生产。     

磁流变液制备的最新进展

介绍了一种新型的智能材料－磁流变液的性能，并对磁流变液的主要组成成分进行了分类总结，阐述了磁流变液制备的最新发展的情况。另外简要介绍了磁流变液应用的方向。     

生长条件对KDP晶体中散射颗粒的影响

利用透射电子显微技术对不同条件下生长的KDP晶体中包裹物进行了观察并测量了其相应尺寸。结果表明，晶体中的生长缺陷、pH值、生长速度和杂质与KDP晶体散射颗粒的形态存在密切关系。     

羰基铁类随机混合吸波材料等效电磁参数的计算

本文为计及多重散射偶极子间的相互作用，引入参量εｈ和μｈ，导得一组公式。它不仅能计算铁氧体类也能计算羰基铁类的随机混合吸波材料的等效电磁参数，均与实验结果吻合良好。     

Ti/Al Interaction and Austenite Grain Control in Crankshaft Manufacturing with 38MnSiVS5 Steel

38MnSiVS5 steel is similar to 38MnVS6 steel (EN), the difference being the addition of a small Ti content. Typical Ti and Al contents in the chemical composition of 38MnSiVS5 steel are Ti=0.020 and Al=0.035 mass%. Both elements combine easily with nitrogen, especially Ti, and it has been observed that relatively high Al levels are harmful for austenite grain size control at reheating temperatures. In this work 38MnSiVS5 steel is used to manufacture a large number of castings, varying only the Ti and Al contents and obtaining ingots with a different Ti/Al ratio in each case. The results show that abnormal growth of the austenitic grain occurs irrespective of the Ti and Al contents, due fundamentally to the partial dissolution and coarsening of TiN precipitates. However, the steels with high Al contents present worse behaviour due to the formation of a second type of precipitates, namely AIN, which quickly dissolve between 1000 and 1100°C, causing a drastic decline in local pinning forces that gives rise to more pronounced abnormal growth of the affected grains.     

用热失重法确定水合粘土水分含量及存在形式

文章以蒙脱土为例，采用热失重法定性定量确定了水合粘土中结合水类型、界限及其相对含量，并与等温吸附法结果进行了对比。结果表明，用该方法得到的水合蒙脱土中各种水分的相对含量及总含水量与等温吸附实验结果相一致。热失重（25~250 ℃）分析结果表明，水合蒙脱土中水分子主要存在自由水、松散吸附结合水、紧密吸附水（强吸附结合水）3种状态，分别对应于25~75 ℃、75~120 ℃、120~230 ℃区间里的失水。从热失重（25~250 ℃）规律来看，仍存在两个明显的转折点p/ps=0.9、0.98，它们为粘土-水体系的两个特征湿度，前者为粘土表面强结合水与松散结合水（渗透结合水）之间的界限，后者为松散结合水与自由水之间的界限，这验证了等温吸附法确定的两个特征湿度及对粘土表面结合水界限划分的正确性。